Popular: Arduino Automation Commodore Iot Raspberry pi
Projects 508
Questions 15
Feedback 209
Blog 15
Sponsorships 25
Apple2-IO-RPi v7
Terence Boldt Jun 25,2024
Apple2-IO-RPi v7PurposeThe purpose of this project is to provide I/O for an Apple II series 8 bit computer via a Raspberry Pi Zero W which is powered by the Apple II expansion bus. This includes using the attached RPi Zero W for it's storage, network and processor to provide new functionality for the Apple II.FeaturesBoot message which waits for RPi to be readyProDOS bootable drive from image stored on RPiProDOS clock driver that uses the RPi clock which is network synchronizedLinux bash shell t...
Raspberry Pi Apple II Apple2
1499
3
8
CYBER.PY Zero-Three
Arnov sharma Jun 25,2024
Greetings everyone, and welcome back.This is CYBER.PY Zero-Three, a Cyberdesk-themed Raspberry Pi PC that is equipped with the Waveshare 7.9-inch ultra-wide HDMI display.This is basically another installment of my previous Cyber.PY projects, which you can see by visiting the links below.https://www.hackster.io/Arnov_Sharma_makes/cyber-py-zero-one-339846https://www.hackster.io/Arnov_Sharma_makes/cyber-py-zero-two-fdd889First, the whole design was modeled in Fusion360. Then it was 3D printed ...
3D printing Commodore SLA
1370
0
6
Raspberry Pi 4B/5 Current Sensor HAT
Jun 22,2024
A current sensor HAT for Raspbery Pi 4B/5
609
0
0
rpitx-coax-pcb-GP1212-GP731
Yatsevich Jun 22,2024
GitHub project page | rpitx-coax-pcbExpansion board for Raspberry PI allowing to use coaxial SMA output instead of direct wire connection to GPIO to connect radio equipment (antennas, amplifiers, switches, etc.) when working with the rpitx package.The PCB is installed by attaching to the GPIO of the Raspberry PI and can be additionally fixed by using the holes on the Raspberry PI and expansion board side.Basic device characteristics:PCB versions: PCB_rpitx-coax-pcb-GP1212-GP731 - ...
RaspberryPI rpitx Radio
907
0
0
rpitx-coax-pcb-NOFILTER
Yatsevich Jun 22,2024
GitHub project page | rpitx-coax-pcbExpansion board for Raspberry PI allowing to use coaxial SMA output instead of direct wire connection to GPIO to connect radio equipment (antennas, amplifiers, switches, etc.) when working with the rpitx package.The PCB is installed by attaching to the GPIO of the Raspberry PI and can be additionally fixed by using the holes on the Raspberry PI and expansion board side.Basic device characteristics:PCB versions: PCB_rpitx-coax-pcb-NOFILTER - no f...
RaspberryPi rpitx Radio
509
0
0
KY-022 Infrared Receiver Module
BARMAN Jun 21,2024
The KY-022 module is an infrared receiver that reacts to 38kHz IR light. It can be used to receive commands from IR remote controllers for TVs, stereos, and other IR transmitter devices. The module provides digital output signals that can be easily interfaced and read by microcontrollers such as Arduino, Raspberry Pi, ESP32, etc. Read continue (schematic, how it works, connection guides, etc.) - KY-022 Infrared Receiver Module.Parts Placement Instructions for PCB:VS1838B IRSMD 595nm Red LED1k Re...
Arduino ESP8266 DIY
2533
0
0
POWER Pi Version 2
Arnov sharma Jun 20,2024
Greetings to everyone, and welcome back.This is Power Pi, a small, integrated Raspberry Pi PC with a built-in lithium-ion battery pack that allows the Pi to be powered wirelessly.This is version 2 of the previously built Power Pi project.In the previous version, there were only two sections: the battery section and the Pi holder. In the new version, we have added a few more sections, which results in a somewhat larger setup than the one previously.We also included an RGB LED setup in this b...
3D printing SLA Arduino
1356
0
3
Raspberry Pi Pico Tire/Tyre Pressure Monitoring System (TPMS)
Teel Jun 15,2024
The Tire light was illuminated on the dash of my 2007 Prius. I ran around checking the air pressure in the tires. Found that a few were perhaps a little low, but not enough to cause the dash light to be lit. I then assumed that one ore more of the TPMS sensors had a dead battery, but how can I know for certain? I took it to the garage and found that yes, one was dead and one had a low battery. The garage replaced them both. This got me to look and see if anyone had built a TPMS display to show t...
Raspberry pi DIY Circuit
2625
0
1
C64 Pico Cart
Secco41 Jun 07,2024
Thanks to cknave for the project, Not tested and I will try and share comments about this project.
Commodore Raspberry pi Retro
1345
0
6
Probe Connector to interface with Breadboard for Raspberry Pi Pico Debug Probe
HARAN Jun 06,2024
This connector PCB is used to connect the Raspberry Pi Pico Debug Probe to the Breadboard. (It is actually used to connect the Probe Plug)Raspberry Pi Pico Debug Probe and Probe Plug are the other project.
DIY Raspberry pi
684
0
0
1 ... 10 11 12 13 14 15 16 17 18 19 20 ...
Popular Creator
Pmanapon
Excellent Engineer
Project: 1 Followers: 15
hackup.net
Excellent Engineer
Project: 17 Followers: 123
Anthony Chiam
Excellent Engineer
Project: 1 Followers: 5
McAleer
Excellent Engineer
Project: 2 Followers: 8
agoktugaydin
Excellent Engineer
Project: 2 Followers: 5
Popular Project
DIY Meshtastic Using ESP32 : Build Your Own Private Off-Grid Network
Project OverviewThis project delivers a complete, custom-designed PCB solution for building Meshtastic mesh network nodes. Unlike traditional communication methods that rely on cellular towers or Wi-F...
? How to Make a DIY Spot Welding Machine at Home for 18650 Batteries | Full Circuit & Working
If you’re working on battery pack projects using 18650 lithium-ion cells, then you know how important a spot welder is. Buying a professional spot welding machine can be expensive, but today, I’ll sho...
Bruce RF Reaper PCB
Explore!https://bruce.computer MCU ESP32 S3 N16R8BATTERY 1000MAH6 WAY BUTTONAW9523 IO EXPANDERNRFCC1101 433MHZNFC ST25R3916VIBROBUZZERIR TX RXIBUTTONSDCARDLEDGPSFLIPPER ZERO HEADER COMPATIBL...
LTS Respooler Control Board
The LTS Respooler is a compact and slightly over-engineered filament Respooler optimized for Bambu Lab spools. It integrates a filament runout sensor and wireless app-connectivity for ease of use.!! I...
MiciMike Google Home mini drop-in PCB by iMike78
MiciMike drop-in PCB replacement for Google Home Mini (Gen-1)MiciMike Home Mini is a drop-in PCB replacement for the "Google Home Mini" (Google's first-generation smart speaker hardware with a Micro-U...
View More
Hot Project Tags
Space Exploratio Virtual reality Microcontroller DIY Synthesizer Weather Station Synthesizer Antenna TVC